Configuring Rapid PVST+
Konfigurasi Switch 1
S1>en
S1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S1(config)#vlan 10
S1(config-vlan)#vlan 20
S1(config-vlan)#vlan 30
S1(config-vlan)#vlan 40
S1(config-vlan)#vlan 50
S1(config-vlan)#vlan 60
S1(config-vlan)#vlan 70
S1(config-vlan)#vlan 80
S1(config-vlan)#vlan 99
S1(config-vlan)#
S1#copy running-config st
S1#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
S1#en
S1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S1(config)#int range f0/1-4
S1(config-if-range)#sw mod tr
S1(config-if-range)#
S1(config-if-range)#sw trunk nat
S1(config-if-range)#sw trunk native vlan 99
S1(config-if-range)#
S1(config-if-range)#ex
S1(config)#int vlan 99
S1(config-if)#
S1(config-if)#ip add 172.17.99.11 255.255.255.0
S1(config-if)#
S1(config)#spanning-tree mod rapid-pvst
S1(config)#spanning-tree vlan 1,10,30,50,70 root primary
S1(config)#
Konfigurasi Switch 2
SW 2
S2>en
S2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S2(config)#int F0/6
S2(config-if)#sw mode acc
S2(config-if)#no sh
S2(config-if)#
S2(config-if)#int F0/18
S2(config-if)#sw mod acc
S2(config-if)#no sh
S2(config-if)#
S2(config-if)#int F0/11
S2(config-if)#sw mod acc
S2(config-if)#no sh
S2(config-if)#
S2(config-if)#ex
S2(config)#vlan 10
S2(config-vlan)#vlan 20
S2(config-vlan)#vlan 30
S2(config-vlan)#vlan 40
S2(config-vlan)#vlan 50
S2(config-vlan)#vlan 60
S2(config-vlan)#vlan 70
S2(config-vlan)#vlan 80
S2(config-vlan)#vlan 99
S2(config-vlan)#
S2#
S2(config)#int f0/6
S2(config-if)#sw acc vlan 30
S2(config-if)#int f0/18
S2(config-if)#sw acc vlan 20
S2(config-if)#int f0/11
S2(config-if)#sw acc vlan 10
S2(config-if)#
S2#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
S2#
S2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S2(config)#int range f0/1-4
S2(config-if-range)#sw mod tr
S2(config-if-range)#switchport trunk native vlan 99
S2(config-if-range)#ex
S2(config)#int vlan 99
S2(config-if)#
S2(config-if)#ip add 172.17.99.12 255.255.255.0
S2(config-if)#
S2(config)#spanning-tree mod ra
S2(config)#spanning-tree mod rapid-pvst
S2(config)#spanning-tree vlan 1,10,20,30,40,50,60,70,80,99 root secondary
S2(config)#
S2(config-if)#spanning
S2(config-if)#spanning-tree portfast
S2(config-if)#
S2(config)#int f0/6
S2(config-if)#spanning
S2(config-if)#spanning-tree portfast
S2(config-if)#spa
S2(config-if)#spanning-tree bp
S2(config-if)#spanning-tree bpduguard en
S2(config-if)#spanning-tree bpduguard enable
S2(config-if)#int f0/18
S2(config-if)#span
S2(config-if)#spanning-tree portf
S2(config-if)#spanning-tree portfast
S2(config-if)#span
S2(config-if)#spanning-tree bp
S2(config-if)#spanning-tree bpduguard en
S2(config-if)#int f0/11
S2(config-if)#span
S2(config-if)#spanning-tree po
S2(config-if)#spanning-tree portfast
S2(config-if)#spannin
S2(config-if)#spanning-tree bpd
S2(config-if)#spanning-tree bpduguard en
S2(config-if)#
Konfigurasi Switch 3
S3>
S3>en
S3#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S3(config)#vlan 10
S3(config-vlan)#vlan 20
S3(config-vlan)#vlan 30
S3(config-vlan)#vlan 40
S3(config-vlan)#vlan 50
S3(config-vlan)#vlan 60
S3(config-vlan)#vlan 70
S3(config-vlan)#vlan 80
S3(config-vlan)#vlan 99
S3(config-vlan)#
S3#copy runni
S3#copy running-config st
S3#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
S3(config)#int range f0/1-4
S3(config-if-range)#sw mod tr
S3(config-if-range)#sw tr native vlan 99
S3(config)#int vlan 99
S3(config-if)#
S3(config-if)#ip add 172.17.99.13 255.255.255.0
S3(config-if)#
S3(config)#spanning-tree mod r
S3(config)#spanning-tree mod rapid-pvst
S3(config)#spanning-tree vlan
S3(config)#spanning-tree vlan 20,40,60,80,99 root primary
S3(config)#
l
